The Autoswitch is a gadget that defines what Cycle Gadgets is all about - a simple, practical, and unique accessory!  Autoswitch allows you to control fog or driving lights without adding an ugly aftermarket switch to your bike.  This is an excellent complement to the PIAA or Motolights auxiliary driving lights we offer, or any other driving/fog lamps on motorcycles OR cars.  There are three types of Autoswitch - a "Positive Trigger" version that works on most bikes, a "Negative Trigger" version for non-CanBUS BMWs with a turn-signal cancel button, and a CanBUS BMW version (R1200GS, R1200RT, R1200ST, K1200GT 2006+, K1200R, and K1200S). To operate the Autoswitch, simply flash your high-beam in a specific sequence, or if you have a BMW press the turn-signal cancel button. The sequence and duration for these actions depends upon the version of the Autoswitch you install. The Autoswitch includes a pre-wired LED that can be positioned in an unobtrusive place to remind you when the lights are on.  If this feature is not desired, the line can be clipped or bundled up in an out-of-the-way location.  The switch module is very small; I fit mine inside the fuse box on my R1100RT with no problems at all. Technical information: The Autoswitch puts out a low current (<200mA) signal, intended to trigger a relay that then activates the lights. If you are using this with a PIAA, Motolight, Hella, etc. set of lights with a supplied wiring harness, that harness will include a relay and nothing else other than the Autoswitch will be needed to complete the installation. Some low-wattage or inexpensive (e.g. Wal-Mart) lights might not include a relay, or if you are doing custom lights you might need to supply your own relay. We sell a 30A automotive relay and socket that is useful for a variety of purposes below.

Model AS-5P - High Beam, Single Press. This version installs on virtually any motorcycle or car, and ties into the high beam circuit. Activate lights by flashing high-beams for a minimum of 0.8 seconds and a maximum of 1.8 seconds. The LED status indicator flashes during that interval to tell you when you can go back to low beam.   $22.95  Qty: # AS-5P Model AS-5P2 - High Beam, Double Press. This version installs on virtually any motorcycle or car, and ties into the high beam circuit. Activate lights by flashing high-beams twice within 2 seconds. This model may be installed on the same vehicle as an AS-5P to allow independent control of two sets of lights.   $22.95  Qty: # AS-5P2 Model AS-5NCY - BMW, Single Press. This version installs on any non-CanBUS BMW that has a separate turn-signal cancel button (works on all R1100, R1150 models; K1200LT; K1200RS; K1200GT through 2004; R1200C. Does not work on R12GS/RT/ST, K1200GT 2005+, K12S/R, or any other CanBUS bike. See AS-6B and AS-6B2). To activate or deactivate lights, press & hold turn signal cancel button for 1 second or longer.   $27.95  Qty: # AS-5NCY Model AS-5N2 - BMW, Double Press. This version installs on any non-CanBUS BMW that has a separate turn-signal cancel button (works on all R1100, R1150 models; K1200LT; K1200RS; K1200GT through 2004; R1200C. Does not work on R12GS/RT/ST, K1200GT 2005+, K12S/R, or any other CanBUS bike. See AS-6B and AS-6B2). To activate or deactivate lights, press & release turn-signal cancel button twice within 2 seconds. This model may be installed on the same bike as an AS-5NCY to allow independent control of two sets of lights. Note: The Autoswitch #AS-5N2 version is out of stock due to parts supply problems. We don't expect to be able to ship these until late July.   $24.95  Qty: # AS-5N2 Model AS-6B2 - BMW CanBUS, Double Press (Tap turn-signal cancel button twice in 2 seconds to activate lights). This version is intended for BMW CanBUS bikes (e.g. R1200GS, R1200RT, K1200GT 2005+, etc.) This version requires considerable disassembly of the bike. Read these instructions (PDF format) before attempting the install. You may want to have it professionally installed. This model may be installed on the same bike as an AS-6B to allow independent control of two sets of lights. For incandescent (halogen) lamps only, will not work with HID. Note: The #AS-6B Autoswitch is discontinued and will no longer be built. The #AS-6B2 is the only CanBus Autoswitch currently available.   $27.95  Qty: # AS-6B2 5-pin DIN style 30A automotive relay. Can be used for NO or NC applications. NO contacts rated 30A, NC contacts 20A. 88 ohm coil (136mA @ 12VDC). Plastic housing. Terminals are 1/4" QD style, can be used with QD female terminals or with pre-wired socket (sold separately). Standardized design for many applications.   Add CG-RLY-SOCKET - Relay Socket with 7.5" Leads ($3.75) $5.00  Qty: # CG-RLY 5-pin DIN style relay socket. Includes leads for both NO and NC connections. Multiple sockets connect together for neat wiring. 7.5" long leads. Power leads 14AWG, coil leads 18AWG.   $3.75  Qty: # CG-RLY-SOCKET